Description
Burks ED11M Base Mounted Turbine Pump End
The Burks ED11M base mounted turbine pump is part of the
Burks ED Series of base mounted regenerative turbine pumps. This listing
is for the ED11M pump end only, part number
000BU00.
The ED11M is designed for low-flow, high-head applications using clean,
non-corrosive, non-abrasive, lower-viscosity liquids. Typical applications
may include boiler feed, condensate return, heat transfer, hot and cold water
circulation, pressure boosting, high pressure spray, and similar services
when the pump curve and system conditions are properly verified.
This pump end uses bronze fitted construction, a bronze impeller with Monel
blades, 2-1/2" NPT suction, 2" NPT discharge, and a
carbon / ceramic / stainless / Buna-N mechanical shaft seal. Browse other
Burks pumps
or view related
pump parts.
Important Ordering Note
This ED11M listing is for the pump end only. Motor, coupling,
base, coupling guard, and assembled base-mounted pump package components
are not included unless quoted separately. Confirm the required motor
horsepower, voltage, phase, enclosure, coupling, base, and guard before
ordering a complete pump assembly.
Key Features
- Burks ED Series base mounted regenerative turbine pump
- ED11M pump end only
- Part number 000BU00
- Bronze fitted construction
- Cast iron casing and power frame
- Bronze impeller with Monel blades
- 11/16" impeller bore
- Bronze raceway
- No. 303 stainless steel shaft
- Carbon / ceramic / stainless / Buna-N mechanical shaft seal
- 2-1/2" NPT suction connection
- 2" NPT discharge connection
- Factory tested pump design
- Self-priming after casing is filled with liquid
Performance Range
| Performance | Details |
|---|---|
| Approximate Capacity Range | 31–60 GPM |
| Approximate Head Range | 20–360 ft |
| Pump Type | Regenerative Turbine |
Connections
| Connection | Size |
|---|---|
| Suction | 2-1/2" NPT |
| Discharge | 2" NPT |
Specifications
| Specification | Details |
|---|---|
| Model | ED11M |
| Part Number | 000BU00 |
| Series | Burks ED Series |
| Configuration | Base Mounted Pump End Only |
| Pump Type | Regenerative Turbine |
| Construction | Bronze Fitted |
| Power Frame Material | Cast Iron |
| Casing Material | Cast Iron |
| Impeller Material | Bronze with Monel Blades |
| Impeller Bore | 0.6875" / 11/16" |
| Raceway Material | Bronze |
| Shaft Material | No. 303 Stainless Steel |
| Shaft Seal Material | Carbon / Ceramic / Stainless / Buna-N |
| Maximum Operating Temperature | 225°F with standard Buna-N seal |
| Maximum Casing Working Pressure | 200 PSI |
| Maximum Inlet Pressure | 50 PSI |
Downloads & Technical References
Repair Parts & Service Support
For repair and service components, browse our
pump parts.
Confirm the exact pump model, part number, seal material, construction,
and nameplate information before ordering repair parts.
Installation & Selection Tips
Confirm that the required duty point falls within the approximate
31–60 GPM and 20–360 ft head performance
range. Verify suction conditions, inlet pressure, fluid temperature, viscosity,
material compatibility, and available NPSH before ordering.
A suction strainer is recommended to help prevent chips, scale, and hard foreign
particles from entering the pump and damaging the raceway or impeller. For boiler
feed, condensate return, heat transfer, pressure boosting, high pressure spray,
or circulation service, confirm the full system requirements before selection.
Frequently Asked Questions
Is the ED11M a complete pump with motor?
This listing is for the ED11M pump end only. Motor, coupling, base, coupling
guard, and complete base-mounted assembly components are not included unless
quoted separately.
What are the connection sizes?
The ED11M has a 2-1/2" NPT suction connection and a 2" NPT discharge
connection.
What performance range does this pump cover?
The approximate ED11M curve range is 31–60 GPM with head from about
20–360 ft. Final selection should be checked against the individual pump curve.
What materials are used in the ED11M?
The ED11M uses bronze fitted construction with cast iron casing and power frame,
bronze impeller with Monel blades, bronze raceway, No. 303 stainless steel shaft,
and a carbon / ceramic / stainless / Buna-N mechanical seal.
Can this be used for boiler feed or condensate return?
Yes, the ED Series may be used for boiler feed or condensate return service
when the required flow, head, temperature, pressure, suction conditions, and
material compatibility are within the pump limits.